TrueDEK Classic Shower Base – 72” x 48”

Regular Price $908.00

SKU: 21053

+ Create a zero-entry shower without modifying joists
+ Structural compression mold GRP offers superior strength, up to 840lbs max.
+ Strong enough to support a wheelchair user and carer in the shower
+ Simple to install, easy to cut, enlarge and customize
+ Pre-sloped with 4 gradient planes for quick, efficient drainage

74844 908
truedek-classic-drains
0
116323
721
722
723
132
125
126
127
128
129
123
124
truedek-waterproofing-kits
0
183
170

Description

Curbless TrueDEK Classic shower bases are made from lightweight yet incredibly strong compression molded glass-fiber reinforced plastic (GRP) which offers superior support for wheelchair users and/or those needing assistance with showering, and is the perfect foundation for ceramic tile, natural stone, or weldable vinyl flooring.

Showers built on TrueDEK Classic bases offer the timeless advantages of zero-entry access which is designed to be wheelchair and disability friendly, as well as easier to clean and safer to use for the whole family, for years to come.

Product Specification:

  • Made from compression molded glass-fiber reinforced plastic (GRP) for superior strength
  • 840lbs max. capacity when installed on 16″ o.c. joist systems, enough to support a wheelchair user and carer
  • Waffle underside ensures rigidity while being lightweight (approx. 92lbs)
  • Install on wooden joists (no need to notch, lower or alter joists), sub-floor, or concrete
  • Can be cut down to size on all sides using standard power tools (within 6″ of drain)
  • Extend size of pitch to comply with ADA regulations using TruePITCH Extension panels
  • 6¼” drain hole diameter
  • Rotate off-center drain hole to avoid conflicts between drain and any sub-floor obstructions
  • 4 pre-sloped gradient planes direct water flow towards drain
  • 2% per foot or greater gradient (varies due to length of pitch)
  • 7/8″ thick around perimeter
  • 1¾” wide leveling rim around perimeter with pre-bored, countersunk pilot holes
  • Finish with tile or stone (between ¼”-1″ thick) or commercial-grade weldable vinyl flooring
  • For tile that is 2″ x 2″ or smaller, conform to the pitched contours of the base; for tile larger than 2″ x 2″, make valley cuts so the tile lays properly on all pre-pitched surfaces
  • Covered by AKW limited lifetime warranty
  • You will need an ARC Waterproofing Kit and Classic Drain assembly
  • For more details, see Specification Sheet
  • Review installation instructions before beginning your project

Reviews

There are no reviews yet.

Be the first to review “TrueDEK Classic Shower Base – 72” x 48””

Your email address will not be published. Required fields are marked *

Specification Sheets

Download Specification Sheet

What you will need

There are no video tutorials for this product.

+ -
I lost the screws for my drain for tile. What sizes do I need?

All the screws that come with the drain for tile are stainless steel, and they are metric sizes and thread counts. These are available at many well-stocked hardware stores in their specialty fastener section (often you'll find an aisle with pull-out drawers, and inside the drawers are all kinds of unique fasteners). Here is the screw information:

1. For the four screws that fasten the adaptor to the foundation, you really can use flat head screws that fit, and they don't have to be metric. We recommend #6 or #8 x 3/4" long, flathead, wood threaded style screws in stainless steel or ceramic coated. Always drill pilot holes before driving these screws.

2. To secure the clamping ring, you'll need M4 x 0.7 x 16mm long stainless steel screws. These have to be metric and the proper size and threading to fit the threaded holes in the adaptor.

Find your nearest ARC distributor

Find ARC bathroom products at 170+ distributors located across the United States & Canada, including a range of national chains and independent merchants.

Learn more

©2024 ARC Inc. All Rights Reserved | Website by Super Digital